SFP/QSFP

The MikroTik XS+85LC01D is a tri-rate 1G/10G/25G multimode optical transceiver — SFP / SFP+ / SFP28 form factor, 850nm VCSEL, dual LC UPC connector, 100m reach on OM3/OM4 multimode fibre, built-in digital diagnostics (optical power, supply voltage, temperature, laser bias current monitoring), -40°C to +85°C tested ambient, MTBF ~100,000 hours at 25°C. No FCC or IC certification published. The correct short-reach multimode transceiver for RB5009, CCR2116, netPower series, CRS, and CSS switches requiring 1G, 10G, or 25G SFP/SFP+/SFP28 connectivity over existing multimode fibre plant at distances up to 100 metres.

The MikroTik XQ+CM0000-XS+ is a QSFP28 to SFP28 form-factor converter — a passive adapter that allows any SFP / SFP+ / SFP28 module (1G / 10G / 25G) to be inserted into a QSFP28 100G/40G port, enabling the use of existing SFP28 transceivers and DAC cables in QSFP28 port-equipped switches without a separate SFP28 switch layer. Tested ambient temperature -20°C to +85°C, MTBF ~100,000 hours at 25°C. No certifications published. The correct port-conversion accessory for CRS504-4XQ-IN, CRS518-16XS-2XQ-RM, CRS510-8XS-2XQ-IN, and any MikroTik or third-party switch with QSFP28 ports where existing SFP28 25G, SFP+ 10G, or SFP 1G modules need to be utilised without rewiring or adding a downstream switch.

The MikroTik XQ+DA0003 is a 3-metre passive direct attach copper (DAC) twinax cable with integrated QSFP28/QSFP+ connectors — dual-rate 100G (QSFP28-to-QSFP28) and 40G (QSFP+-to-QSFP+), no optical transceivers, no fiber, plug-and-play copper interconnect. Compatible with MikroTik CCR2216, CRS504-4XQ-IN/OUT, CRS510-8XS-2XQ-IN, CRS518-16XS-2XQ-RM, and any IEEE 100GBASE-CR4 / 40GBASE-CR4 compliant QSFP28 or QSFP+ port. Flexible twinax construction. MTBF ~100,000 hours at 25°C. No certifications listed (passive copper assembly). USD 59.00.

The S+85DLC03D is a 10G SFP+ transceiver designed for 300-meter Multi Mode fiber connections. It features an LC connector and is compatible with a wide range of MikroTik and non-MikroTik SFP+ devices.

The S+AO0005 is a 5-meter SFP+ Active Optics direct attach cable that supports 10Gbps connectivity. It provides a cost-effective solution for connecting two SFP/SFP+ devices within or across adjacent racks.

The MikroTik XQ+DA0001 is a 1-metre passive direct attach copper (DAC) twinax cable with integrated QSFP28/QSFP+ connectors — dual-rate 100G (QSFP28-to-QSFP28) and 40G (QSFP+-to-QSFP+), no optical transceivers, no fiber, plug-and-play copper interconnect. The 1m sibling to the XQ+DA0003 (3m, USD 59.00) — correct for side-by-side rack unit or same-shelf installations where a 3m cable would add unnecessary slack. Compatible with MikroTik CCR2216, CRS504-4XQ-IN/OUT, CRS510-8XS-2XQ-IN, CRS518-16XS-2XQ-RM. MTBF ~100,000 hours at 25°C. No certifications listed (passive copper assembly). USD 39.00.

The XS+DA0003 is a 3-meter direct attach cable supporting SFP 1G, SFP+ 10G, and SFP28 25G standards. It provides an affordable, low-latency solution for connecting devices within or across adjacent racks for high-speed networking.

The S-RJ01 is an RJ45 SFP module supporting 10/100/1000M speeds for copper Ethernet connections. Compatible with most Gigabit SFP ports, it offers seamless integration with various networking devices.

The XS+DA0001 is a 1-meter direct attach cable supporting SFP 1G, SFP+ 10G, and SFP28 25G standards. It offers a cost-effective, low-latency solution for connecting devices within or across adjacent racks.

The S-31DLC20D is a 1.25G SFP transceiver with a 1310nm Dual LC connector, designed for Single Mode fiber connections up to 20 km. It features DDM support and compatibility with a wide range of MikroTik and non-MikroTik devices.