New products

The SYNOXX EDQPY-5-26 is a 100G QSFP28 to QSFP28 passive direct attach copper 
(DAC) cable delivering 100Gbps over a 5-metre 26AWG twinax connection — purpose-built 
for extended-rack and cross-row 100G deployments where 1m and 3m cables fall short, 
including end-of-row switch connections, long cable tray runs, and flexible spine-to-leaf 
links requiring extra reach on the passive copper budget. Based on a 4×25G architecture, 
compliant with SFF-8636 and IEEE 802.3bj, with a two-wire I2C interface for monitoring 
and control, low power consumption, and low crosstalk across the full 5m run. 
Hot-pluggable, RoHS compliant, and IC Certified.

The SYNOXX EQP85Y-01D is a 100G QSFP28 SR4 optical transceiver delivering 100Gbps 
over multimode fiber using a 4×25G parallel VCSEL array — transmitting and receiving 
across four simultaneous 25G optical lanes via an 8-fiber MPO ribbon connector, 
supporting distances up to 100m on OM3 and OM4 multimode fiber for high-density 
100G data centre switching, 100G parallel breakout deployments, and any 100G 
application requiring MPO-based multimode fiber infrastructure. Compliant with 
QSFP28 MSA and IEEE 802.3bm, featuring integrated Digital Diagnostic Monitoring 
(DDM) for real-time temperature, voltage, TX/RX optical power, and bias current 
monitoring with low power consumption. Hot-pluggable, RoHS compliant, and IC 
Certified.

The SYNOXX EDSP2X-5-26 is a 25G SFP28 to SFP28 passive direct attach copper (DAC)
cable delivering 25.78Gbps over a 5-metre 26AWG twinax connection — built for
extended-rack and end-of-row 25G deployments where 1m and 3m cables fall short,
including cross-rack leaf-to-server links, overhead cable tray runs spanning multiple
rack units, and 100G breakout target connections requiring routing slack across
rack boundaries. Compliant with SFP28 MSA and SFF-8402, featuring a hot-pluggable
SFP28 form factor, fully passive copper with no active components, and operating
temperature range of 0°C to 70°C. Hot-pluggable, RoHS compliant, and IC Certified.

The SYNOXX EDSPX-5-24 is a 10G SFP+ to SFP+ passive direct attach copper (DAC) 
cable delivering 10Gbps — and backward-compatible 1Gbps — over a 5-metre 24AWG 
twinax connection, purpose-built for extended-rack and end-of-row 10G deployments 
where 1m and 3m cables fall short, including cross-rack ToR switch-to-server links, 
long overhead tray runs, and flexible 10G fabric connections requiring extra passive 
copper reach. Compliant with SFP+ MSA, SFF-8431, and SFF-8432 standards, with 
power consumption below 0.2W per end, hot-pluggable SFP+ form factor, and 
operating temperature range of 0°C to 70°C. Hot-pluggable, RoHS compliant, and 
IC Certified.

The SYNOXX ESP3112-20D is a 1.25G SFP LX optical transceiver delivering Gigabit 
Ethernet and Fibre Channel connectivity over single-mode fiber (SMF) up to 20km 
using a 1310nm FP laser transmitter — the standard long-reach 1G fiber module for 
campus backbone links, building-to-building connections, and metro-edge deployments 
where multimode fiber falls short. Features Digital Diagnostic Monitoring (DDM) with 
real-time temperature, voltage, TX/RX power, and bias current monitoring, plus PIN 
photodiode receiver with integrated TIA and MCU control, compliant with SFP MSA and 
SFF-8472 standards. Hot-pluggable, RoHS compliant, and IC Certified.

The SYNOXX ESP8512-055D is a 1.25G SFP SX optical transceiver delivering Gigabit 
Ethernet and Fibre Channel connectivity over multimode fiber (MMF) up to 550 metres 
using an 850nm VCSEL transmitter — the standard choice for access-layer 1G fiber 
links and 1G Fibre Channel connections over OM2, OM3, or OM4 multimode infrastructure. 
Supports data rates up to 1.25Gbps with Digital Diagnostic Monitoring (DDM), PIN 
photodetector receiver, and compliance with SFP MSA and SFF-8472 standards, with low 
power consumption and a standard LC duplex connector. Hot-pluggable, RoHS compliant, 
and IC Certified.

The SYNOXX ES-T7-R is a 10GBase-T SFP+ copper transceiver delivering 10Gbps data 
transfers over standard Cat6a or Cat7 twisted-pair cables up to 100 metres — 
eliminating the need for fiber optics in short-to-medium range enterprise and data 
centre deployments. Supports 10G and 1G data rates with a maximum power consumption 
of 2.5W, hot-pluggable SFP+ form factor, and compliance with IEEE 802.3 and SFP+ MSA 
standards. Hot-pluggable, RoHS compliant, and IC Certified for Canada and the US.

The MikroTik MT-HotSwapFan is a hot-swappable replacement fan designed for MikroTik's newest high-performance devices, including the flagship CCR2216 and CRS518. It allows you to replace a failed fan without shutting down or restarting the device, eliminating unnecessary downtime. An essential spare for any network environment where continuous operation is a priority.

A pair of industrial-grade 10G SFP+ BiDi modules for single-mode links up to 10 km over a single fiber strand. By transmitting and receiving on split wavelengths (1270/1330 nm), the pair delivers efficient long-distance connectivity while halving fiber requirements. Built-in DDM monitors optical power, voltage, temperature, and laser bias current in real time.

Outdoor 5G CPE with an omnidirectional antenna system that connects to the best available network without antenna realignment. Built-in eSIM and microSIM support, GNSS positioning (GPS, Galileo, BeiDou, QZSS), and Gigabit Ethernet with PoE-in. IP67-rated and EN 60945 maritime certified for ports, marinas, industrial sites, and urban or backup deployments.