100G AI Networking

The MikroTik CCR2216-1G-12XS-2XQ is MikroTik's flagship cloud core router — Amazon Annapurna Labs AL73400 16-core ARM64 at 2,000 MHz, Marvell Prestera Aldrin2 98DX8525 switch chip (L3 hardware offloading, 4× 25G CPU lines), 16 GB DDR4 RAM, 128 MB NAND, 2× M.2 SATA slots, RouterOS v7 License 6, 12× SFP28 (25G), 2× QSFP28 (100G), 1× GbE, RJ45 serial console, 2× hot-swap AC PSU (100–240V, 50–60 Hz), 4× hot-swap fans, 128W max / 80W without attachments, CPU + PCB + voltage monitors, IP20, -20°C to +60°C, MTBF ~200,000 hours at 25°C. CE, EAC, RoHS — no FCC, no IC. Includes 2× IEC cord, rack ears, cable management brackets, K-82 fastening set. USD 2,795.00.

All-in-one storage, networking and container platform for enterprise environments. 20 U.2 NVMe bays, 2× 100G QSFP28, 4× 25G SFP28, 4× 10G SFP+ and 2× 10G Ethernet, a 16-core 2 GHz ARM CPU with 32 GB ECC DDR4, 98DX4310 switch chip with L3HW offloading, dual hot-swap power supplies and RouterOS v7 (ROSE edition, licence level 6). No subscriptions, no paywalls.

The MikroTik CRS518-16XS-2XQ-RM is an enterprise-grade 1U rack-mount switch delivering 16× 25 Gigabit SFP28 ports and 2× 100 Gigabit QSFP28 ports, all driven by the Marvell Prestera Aldrin2 (98DX8525) switch chip with a non-blocking switching fabric of up to 1.2 Tbps. The 25G SFP28 ports are fully backward compatible with 10G and 1G SFP devices. Dual hot-swap power supplies with a 100–240 V AC input range and four active cooling fans ensure reliable operation in demanding data centre and enterprise deployments. Running RouterOS v7 with a Level 6 licence, it supports VLAN (802.1Q, 802.1ad), L3 hardware offloaded routing, ACL, LACP, MLAG, and Jumbo frames — making it a powerful and cost-effective core or aggregation switch for high-density 25G and 100G networks.

The MikroTik CRS510-8XS-2XQ-IN is a compact 1U 100 Gigabit data centre switch — 8× 25G SFP28 ports + 2× 100G QSFP28 ports, Marvell 98DX4310 Prestera switch ASIC, single-core MIPSBE QCA9531 at 650 MHz, 128 MB RAM, 32 MB FLASH, RouterOS v7 License 5 / SwitchOS (dual-boot), 1× 10/100 Ethernet management port, RJ45 serial console, 5 power input options (2× hot-swap AC PSU slots 100–240V + DC jack 36–57V + 802.3bt PoE-in 42.5–57V + 2-pin terminal 36–57V), 2-fan active cooling, IP20, -40°C to +70°C, MTBF ~200,000 hours at 25°C. CE, EAC, RoHS certified. Includes 2× IEC cord, rack ears for CRS510, K10 screw kit, connector plug. 

The SYNOXX EQP29Y-10D is a 100G QSFP28 LR4 optical transceiver delivering 100Gbps 
transmission over single-mode fiber up to 10km using four LAN Wavelength Division 
Multiplexing (LWDM) channels around 1310nm — a standard LC duplex interface 
enabling long-reach 100G data centre interconnects, inter-building campus links, 
and metro-edge telecom connections without MPO ribbon fiber infrastructure. 
Compliant with QSFP28 MSA and IEEE 802.3ba, featuring a CAUI-4 (4×25G) electrical 
host interface, integrated Digital Diagnostic Monitoring (DDM) for real-time 
temperature, voltage, TX/RX power, and bias current monitoring, and low power 
consumption. Hot-pluggable, RoHS compliant, and IC Certified.

The MikroTik XQ+31LC02D is a 100 Gigabit QSFP28 optical transceiver module designed for single-mode fibre links of up to 2 kilometres. It uses the CWDM4 (Coarse Wavelength Division Multiplexing) architecture, transmitting across four separate wavelengths — 1271 nm, 1291 nm, 1311 nm, and 1331 nm — over a standard Dual LC UPC connector, making it compatible with widely available OS2 single-mode fibre patch cables. The XQ+31LC02D is well suited for inter-building, campus, or data centre interconnects where DAC cables or short-reach multimode optics cannot cover the required distance, and is compatible with MikroTik's QSFP28-equipped core switches and routers including the CCR2216, CRS504, CRS518, CRS510, and CRS520.

The SYNOXX EQP85Y-01D is a 100G QSFP28 SR4 optical transceiver delivering 100Gbps 
over multimode fiber using a 4×25G parallel VCSEL array — transmitting and receiving 
across four simultaneous 25G optical lanes via an 8-fiber MPO ribbon connector, 
supporting distances up to 100m on OM3 and OM4 multimode fiber for high-density 
100G data centre switching, 100G parallel breakout deployments, and any 100G 
application requiring MPO-based multimode fiber infrastructure. Compliant with 
QSFP28 MSA and IEEE 802.3bm, featuring integrated Digital Diagnostic Monitoring 
(DDM) for real-time temperature, voltage, TX/RX optical power, and bias current 
monitoring with low power consumption. Hot-pluggable, RoHS compliant, and IC 
Certified.

The SYNOXX EDQPY-5-26 is a 100G QSFP28 to QSFP28 passive direct attach copper 
(DAC) cable delivering 100Gbps over a 5-metre 26AWG twinax connection — purpose-built 
for extended-rack and cross-row 100G deployments where 1m and 3m cables fall short, 
including end-of-row switch connections, long cable tray runs, and flexible spine-to-leaf 
links requiring extra reach on the passive copper budget. Based on a 4×25G architecture, 
compliant with SFF-8636 and IEEE 802.3bj, with a two-wire I2C interface for monitoring 
and control, low power consumption, and low crosstalk across the full 5m run. 
Hot-pluggable, RoHS compliant, and IC Certified.

The MikroTik XQ+85MP01D is a dual-rate QSFP+/QSFP28 fibre transceiver module supporting both 40 Gigabit and 100 Gigabit operation over multimode fibre. Using an 850 nm wavelength and a 12-fibre 1×12 MTP/MPO connector in an SR4 configuration, it achieves link distances of up to 100 metres — making it well suited for high-density data centre and core switching deployments within a building or campus. It is compatible with MikroTik's 40G/100G QSFP28-equipped switches and routers such as the CCR2216, CRS504, and CRS518, and provides a cost-effective way to add short-reach 40G or 100G multimode fibre connectivity to any supported platform.

The SYNOXX EDQPY-4SP3 is a 100G QSFP28 to 4×SFP28 passive direct attach copper 
(DAC) breakout cable that splits a single 100G QSFP28 port into four independent 
25G SFP28 connections over 3 metres of twinax copper — enabling cost-effective 
25G server and storage connectivity from a 100G spine or leaf switch port without 
additional transceivers. Compliant with IEEE 802.3bj, SFF-8636, and SFF-8402 
standards, featuring EEPROM support for device identification, low insertion loss, 
and passive operation with no active components required. Hot-pluggable, RoHS 
compliant, and IC Certified.