AI Networking & Data Center

6-speed RJ45 module that brings 10M, 100M, 1G, 2.5G, 5G and 10G Ethernet over familiar twisted-pair copper to any MikroTik SFP+ port — no optical fiber required. The current r3 revision is based on the Marvell MV-CUX3610M, draws 1.5 W max, supports 10GBASE-T links up to 100 m over Cat6/7 and jumbo frames on all advertised speeds.

The MikroTik XS+85LC01D is a cost-effective multimode SFP/SFP+/SFP28 transceiver module supporting 1.25G, 10G, and 25G data rates over distances of up to 100 metres via a Dual LC UPC connector. Operating at 850 nm wavelength, it is compatible with a wide range of MikroTik devices including the RB5009, CCR2116, netPower series, and various CRS and CSS switches. Built-in digital diagnostics provide real-time monitoring of key transceiver parameters to assist with network health visibility and proactive maintenance planning.

The MikroTik XQ+DA0003 is a 3-metre passive Direct Attach Copper (DAC) twinax cable with QSFP+ to QSFP+ and QSFP28 to QSFP28 connectors, supporting both 40 Gigabit and 100 Gigabit data rates. It is designed for direct short-reach interconnects between QSFP28-equipped MikroTik devices such as the CCR2216, CRS504, CRS518, CRS510, and CRS520, offering a latency-free, plug-and-play alternative to optical transceivers and fibre patch cables for rack-to-rack or within-cabinet connections. The 3-metre length provides enough reach to comfortably span adjacent rack units or nearby racks while keeping cable management tidy and installations clean.

The S+85DLC03D is a 10G SFP+ transceiver designed for 300-meter Multi Mode fiber connections. It features an LC connector and is compatible with a wide range of MikroTik and non-MikroTik SFP+ devices.

The SYNOXX ES-T5-R-3 is a 10GBase-T SFP+ copper transceiver supporting 
multi-rate 10G/5G/2.5G/1G Ethernet over RJ45, with a 30m reach on Cat 6a/7 
cable. Hot-pluggable, RoHS compliant, and IC certified for Canada and the US.

The SYNOXX EB23X-10D/EB32X-10D is a matched 10G SFP+ BiDi transceiver pair enabling 
bidirectional 10Gbps transmission over a single strand of single-mode fiber up to 10km, 
using complementary wavelengths of 1270nm TX/1330nm RX and 1330nm TX/1270nm RX. 
Supports data rates up to 10Gbps with Digital Diagnostic Monitoring (DDM), DFB 
transmitter, APD receiver, and power consumption of ≤1.5W per module, compliant with 
IEEE 802.3ae and SFP+ MSA standards. Hot-pluggable, RoHS compliant, and IC Certified.

The SYNOXX ESP852X-01D is a 25G SFP28 SR optical transceiver delivering 25.78Gbps 
transmission over multimode fiber — up to 100m on OM4, 70m on OM3, and 20m on OM2 
— using an 850nm VCSEL laser and PIN photodiode, purpose-built for high-density 25G 
Ethernet switching, 5G CPRI fronthaul, and 100G breakout target deployments. 
Features a hot-pluggable SFP28 form factor, LC duplex connector, and Digital 
Diagnostic Monitoring (DDM) via SFF-8472, with low power consumption and compliance 
with IEEE 802.3cc and SFF-8402 standards. Hot-pluggable, RoHS compliant, and IC 
Certified.

The MikroTik MT-HotSwapFan is a hot-swappable replacement fan designed for MikroTik's newest high-performance devices, including the flagship CCR2216 and CRS518. It allows you to replace a failed fan without shutting down or restarting the device, eliminating unnecessary downtime. An essential spare for any network environment where continuous operation is a priority.

The SYNOXX EDQPY-1 is a 100G QSFP28 to QSFP28 passive direct attach copper (DAC) 
cable delivering 100Gbps data transfers over a 1-metre twinax connection using a 
4×25G lane architecture — the ideal same-rack interconnect for 100G spine-leaf 
switching environments. Compliant with SFF-8636 and IEEE 802.3bj, featuring a 
two-wire I2C interface for monitoring and control, low crosstalk, and power 
consumption under 1.5W per end. Hot-pluggable, RoHS compliant, and IC Certified.

The SYNOXX EDSP2X-3 is a 25G SFP28 to SFP28 passive direct attach copper (DAC) 
cable delivering 25.78Gbps over a 3-metre twinax connection — purpose-built for 
adjacent-rack 25G connections where 1-metre cables fall short, including cross-rack 
leaf-to-server links, flexible cable management through overhead trays and 
under-floor pathways, and 100G breakout target deployments with extra slack. 
Compliant with SFP28 MSA, SFF-8402, and IEEE 802.3by, featuring a hot-pluggable 
SFP28 form factor, low power consumption, and a fully passive copper signal path 
with no active components. Hot-pluggable, RoHS compliant, and IC Certified.